Ahnu

2 lb Stainless Steel Tumbling Media Pins - 0.047" Diameter, 0.255" Length

Description: The highest quality stainless steel produced and cut in Germany0.047" Diameter (1.1938mm)0.255" Length (6.477mm)Manufactured from extremely tough 302/304 stainless steel so the pins will last for thousands of cleaningsPackage includes 2 pounds of reusable precision cut pins for use in rotary or magnetic tumblersStainless steel pins never wear out and will last a lifetime. These are perfect for use in a wet tumbler for polishing brass, steel, aluminum, or titanium. Most commonly used for brass cartridge cleaning, the .047" diameter prevents the pins from getting stuck side by side in flash holes but they will pass through all flash holes one at a time. Fill your tumbler with pins and brass but be sure to leave space to allow tumbling action. Add clean hot water until the tumbler is nearly full. Cold water will work just fine but hot water cleans faster. Add approximately ½ tablespoon Dawn liquid dish detergent (or comparable brand) per 1 lb of brass. The amount of detergent used is not critical but must be enough to ensure good suds remain at the end of the cycle. Run until clean which is typically between 30 minutes and 2 hours. When first starting out check every 15 minutes to see if additional cleaning is necessary. If you don?t see suds after you open your tumbler either you are not using enough soap or the soap is breaking down from running too long. Optional: To achieve the best possible shine add a tablespoon of Lemi Shine dishwasher detergent powder per 1 quart of water. The active ingredient in Lemi Shine is citric acid which dissolves zinc. Remove, rinse, and separate the brass immediately upon stopping the tumbler. As soon as the agitation stops the dirt will start to stick back on the brass so don?t leave it sitting idle in dirty water. Shake dry the brass in a colander and then pour them into the center of a large towel laid out flat. Gather the corners of the towel and roll them around to remove as much water as possible. From there air dry them several days on plastic trays with an occasional turn.

Price: 27.95 USD

Location: Chattanooga, Tennessee

End Time: 2024-08-16T16:28:21.000Z

Shipping Cost: 0 USD

Product Images

2 lb Stainless Steel Tumbling Media Pins - 0.047" Diameter, 0.255" Length

Item Specifics

Return shipping will be paid by: Seller

All returns accepted: Returns Accepted

Item must be returned within: 30 Days

Refund will be given as: Money back or replacement (buyer's choice)

Country/Region of Manufacture: Germany

MPN: BCPINS-2

Brand: BC Precision

Type: Tumbling Media

Recommended

B.C.Rich IRONBIRD MK1 Precision Bass Brown  Electric Bass New with Gigbag
B.C.Rich IRONBIRD MK1 Precision Bass Brown Electric Bass New with Gigbag

$1949.33

View Details
500 ct Copper Plated Steel Metal BBS 4.5mm (.177 Cal) - BC Precision
500 ct Copper Plated Steel Metal BBS 4.5mm (.177 Cal) - BC Precision

$9.99

View Details
300 3/8" Inch G25 Precision 440 Stainless Steel Bearing Balls
300 3/8" Inch G25 Precision 440 Stainless Steel Bearing Balls

$53.95

View Details
Golden Bear BC-03 Precision Milled 52° Gap Wedge Steel Shaft Right Handed Club
Golden Bear BC-03 Precision Milled 52° Gap Wedge Steel Shaft Right Handed Club

$18.99

View Details
Four Bicycle 1/4" x 9 Ball Bearings with Retainer BC Precision NEW
Four Bicycle 1/4" x 9 Ball Bearings with Retainer BC Precision NEW

$8.99

View Details
2 NEW BC PRECISION UCP205-16 PILLOW BLOCK BEARINGS NIB ***MAKE OFFER***
2 NEW BC PRECISION UCP205-16 PILLOW BLOCK BEARINGS NIB ***MAKE OFFER***

$24.99

View Details
Cuisinart SM-50BC Precision Master 5.5-Quart Stand Mixer (Silver) - Brand New
Cuisinart SM-50BC Precision Master 5.5-Quart Stand Mixer (Silver) - Brand New

$132.00

View Details
BC Precision Garage Door Rollers Nylon with 4" Stems
BC Precision Garage Door Rollers Nylon with 4" Stems

$8.14

View Details
100 1/16" 0.0625" BC Precision Si3N4 Silicon Nitride Ceramic Bearing Balls G5
100 1/16" 0.0625" BC Precision Si3N4 Silicon Nitride Ceramic Bearing Balls G5

$18.10

View Details
Dillon RL550B/C Precision Machined Billet Toolhead, (1.08 Thick Like OEM) USA
Dillon RL550B/C Precision Machined Billet Toolhead, (1.08 Thick Like OEM) USA

$20.99

View Details