Description: FOR SALE, A NEW, HOLYBRO NVIDIA CARRIERBOARD WITH PIXHAWK 6X PRO, GPS AND CABLES. PURCHASED FOR A PROJECT WHICH IT WAS DECIDED TO USE DIFFERENT COMPONENTS, THUS MAKING THESE COMPONENTS NO LONGER NECESSARY! Description (From the Holybro website) The Holybro Pixhawk Jetson Baseboard is based on the Pixhawk Autopilot Bus open-source specification and the NVIDIA Jetson Orin NX/Nano Carrier Board. The Pixhawk Autopilot Bus (PAB) Form Factor enables this to be used with any PAB flight controller such as the Pixhawk 6X Feature Combines the power of Pixhawk & Nvidia Jetson in a single board Nvidia Jetson & Pixhawk connected via UART, CAN, and ethernet switch Pixhawk Autopilot Bus (PAB) Form Factor Compatible with Jetson Orin NX & Orin Nano 2x M.@ key for WiFI/Bluetooth & NVMe SSD Pixhawk 6X Pro (ICM-45686) Processors & Sensors FMU Processor: STM32H753 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM IO Processor: STM32F103 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM On-board sensors (Shipping Currently, Rev8) Accel/Gyro: 3x ICM-45686 (with BalancedGyro™ Technology) Barometer: ICP20100 & BMP388 Mag: BMM150 Baseboard Port & Connection Jetson Connectors 2x Gigabit Ethernet port - Connected to both Jetson & Autopilot via Ethernet switch (RTL8367S) - Ethernet Switch powered by circuit as the Pixhawk - 8-pin JST-GH - RJ45 2x MIPI CSI Camera Inputs - 4 Lanes each - 22-Pin Raspberry Pi Cam FFC 2x USB 3.0 Host Port - USB A - 5A Current Limit 2x USB 2.0 Host Port - 5-Pin JST-GH - 0A Current Limit USB 2.0 for Programming/debugging - USB-C 2 Key M 2242 for NVMe SSD - PCIEx4 2 Key E 2230 for WiFi/BT - PCIEx2 - USB - UART - I2S Mini HDMI Out 4x GPIO - 6-pin JST-GH CAN Port - Connected to Autopilot’s CAN2 (4 Pin JST-GH) SPI Port - 7-Pin JST-GH I2C Port - 4-Pin JST-GH I2S Port - 7-Pin JST-GH 2x UART Port - 1 for debug - 1 connected to Autopilot’s telem2 Fan Power Port IIM42652 IMU Input Power - XT30 Connector - Voltage Rating: 7-21V (3S-4S) - Separate input power circuits than the Autopilot to ensure flight safety - Holybro UBEC 12A (3-14S) can be used for application above 4S - Note: The Pixhawk Jetson Baseboard onboard BEC is only rated for 7-21V (3S-4S). Using the external "UBEC 12A (3-14S)" can provides redundancy and easier replacement in case of BEC failure. Power Requirements 8V/3A Minimum Depends on Usage and Peripherals Autopilot Connectors Pixhawk Autopilot Bus Interface - 100 Pin Hirose DF40 - 50 Pin Hirose DF40 Redundant Digital Power Module Inputs - I2C Power Monitor Support - 2x – 6 Pin Molex CLIK-Mate - Power Path Selector w/ Overvoltage Protection Voltage Ratings: - Max input voltage: 6V - USB Power Input: 4.75~5.25V Full GPS Plus Safety Switch Port - 10-Pin JST-GH Secondary (GPS2) Port - 6-pin JST-GH 2x CAN Ports - 4 Pin JST-GH 3x Telemetry Ports with Flow Control - 2x 6-Pin JST-GH - 1 is connected to Jetson’s UART1 Port 16 PWM Outputs - 2x 10-Pin JST-GH UART4 & I2C Port - 6-Pin JST-GH 2x Gigabit Ethernet port - Connected to both Jetson & Autopilot via Ethernet switch (RTL8367S) - 8-pin JST-GH - RJ45 AD & IO - 8-Pin JST-GH USB 2.0 - USB-C - 4-pin JST-GH DSM Input - 3-pin JST-ZH 1.5mm Pitch RC in - PPM/SBUS - 5-pin JST-GH SPI Port - External Sensor Bus (SPI5 - 11-Pin JST-GH 2x Debug Port - 1 for FMU - 1 for IO - 10-Pin JST-SH Dimensions (Without Jetson and Flight Controller Module) 126x80x38mm Weight With Jetson, Heatsink, Flight Controller, M.2 SSD, M.2 Wi-Fi Module 203.2g UBEC-12A Specifications Input voltage: 3~14S (XT30) Output voltage: 6.0V/7.2V/8.0V/9.2V (recommend 7.2V if supplying power to Jetson Board) Output Current - Continuous: 12A - Burst: 24A Size: 48x33.6x16.3 mm Weight: 47.8g
Price: 1250 USD
Location: Destin, Florida
End Time: 2025-01-27T19:14:38.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
All returns accepted: ReturnsNotAccepted
Brand: Holybro
Compatible Brand: Ardupilot
Type: Flight Controller
Color: Black
Model: Pixhawk Jetson Baseboard Bundle
Compatible Fuel Type: Any
MPN: 20280
Country/Region of Manufacture: China
Compatible Scale: All
