Ortur Laser Master 2 Ultimate Upgrade Kit | Printed Parts (No Tubing/Belts)

Description: This is the Ultimate Upgrade Kit for your Ortur Laser Master 2 laser engraver or laser printer. Have you been piecing together all of your mods for your LM2? We put them all in one package so you can take an already great laser and take it to it's limits. This listing comes WITHOUT 6 feet of air tubing and belts for the tensioners. This package has the printed parts only and their associated screws. If you need tubing and belts please view this listing - http://www.ebay.com/itm/333941727568In this kit KGD has included:- Low Profile Air Assist - Z Axis Adjuster Kit- Belt Tensioners- Retaining Feet adjustable height using common building bricks.- Focus Card (for seeing beam better)- T-Handle Wrench (and tool holder for your frame)- U Block End Stop Spacer- Focus Spacer- Nozzle Adjuster Package (6 extra nozzles) Item Descriptions------Air Assist Ortur Laser Master 2 Get deeper cuts by removing the debris with air assist, cleaner engravings and overall better performance. If you have shop air that is recommend between 20-25psi. Small pumps will show great improvement as well but not as good as the larger pumps. Links to suggested pumps upon request.We prefer the side air style rather than the lens covering style. The K40 community experienced the same evolution. Which is now back to some very modern tested over the lens style that some very nice machinist made that created proper air seals. The reason this happens is due to the venturi effect that makes the nozzle a vacuum cleaner, pulling smoke in above, dirtying your lens faster. There are also problems potentially with moisture if not properly handled.If you would like to try both styles shoot me a message I've got special deals I'd love to start getting feedback on what you all think, we carry both styles :)Tools Required:-2mm allen wrench-2.5mm allen wrenchInstall:-Attach link pieces and nozzle to attachment bracket-Install the attachment bracket to the moduleusing the provided screws-Attach the hose holder joint to other ball joint on attachment bracket-Install your 6mm hose (not supplied)-Secure hose with zip ties to the wire loom-Place Nozzle at 45 Degrees 2-3mm from laser dot on workpiece.-----Z Axis AdjusterGives you 40mm of Z travel for quick and easy focusYOU NEED TO ADJUST YOU ENDSTOPIncludes U-block to work as a spacer (see photos)we recommend just moving the end-stop and not using the spacer (see photo)you only need to remove the acorn nuts then remove the plate that your laser module is attached to. See the photos on how to attach to z adjuster then reinstall on you carriage.Uses 4mm allen wrench to adjust, includes Tool Holder and T-Handle wrench This can work with either the Ortur 15W or 20W or the Neje 30W or 40W modules. It will only attach either of those modules to the Ortur Laser Master 2 (square) frame. Will not work with Neje frames. ----- Bit Drive & Knob PackEasily raise and lower your King Gubby Z Axis Adjuster with our upgraded knobs. If you aren't needing to adjust your module's height by much, our knobs make minor adjustments a breeze. Choose one or buy the variety pack if you like different adjusting styles (or have multiple lasers to adjust). Includes:- Knob(s) that you purchase (optional)- Bit Drive- Hex Bit- Tension Spacers -----Belt TensionersThis set of 3 Belt tensioners for the Ortur Laser Master 2 (LM2) let's you adjust the belt tension on your DIY laser printer.Finally you can achieve perfect tension :)Hand tighten or hand loosen the threaded knob to make the adjustment.DO NOT OVER TIGHTEN YOUR BELTS!!!Please refer to "Belt Tension" by RF of youtube - Belt Tension - YouTubeYou may need to Replace your belts with longer belts, to see if your belts are long enough-You need to remove the washers that previously Locked your belt on the side that you install the tensionersX belt needs to be at least 625mmY belt needs to be at least 640mmThese are the minimum if you are cutting belt off a roll leave a little extraGT2 timing belt 6mm wide is what you need (not included in this package)-----Retaining FeetCustom 3D printed supports for the Ortur Laser Master 2 Laser Engraver. Keep your printer from vibrating or moving around while engraving by attaching these fasteners to the bottom of your LM2. With these stabilizers you can expect better stability and functionality while laser printing. Compatible with All Major Brand building bricks (LARGE - 2.5" x 1.25"). Uses 2x4 blocks (Building Bricks not included) These are for the large style bricks. set of 4 Install Video - https://www.youtube.com/watch?v=oj25wUw-2sENOTE - Z AXIS AND BELT TENSIONER INSTALLATION VIDEO CAN BE FOUND ON THE EDGE OF TECH ON YOUTUBE:How to Upgrade Your Cheap Laser Engraver Machine - Ortur Laser Master 2 - YouTube --Credits and Sources:Z Axis AdjusterOriginally from the design (I Have permission and pay royalties)By PLAY3Rone977Remixed by paulmacdermotThen Modified my myself for easy install and I tightened up the tolerance to remove wobbleThe T-Handle wrench is designed by KezatBelt TensionersRemix of the belt tensioner by Misterguru Knobs designed by Perinskihttps://www.thingiverse.com/thing:3778822/filesKnobs designed by Kezathttps://www.thingiverse.com/thing:1316060/files

Price: 89.99 USD

Location: San Diego, California

End Time: 2023-12-31T22:07:49.000Z

Shipping Cost: 10.2 USD